Deckorators CXT8 Rail Bedienungsanleitung PDF herunterladen

Deckorators

CXT

8' Rail Installation Instructions

For Installations Using Co-Extruded Composite,

Classic, Estate, Twist and Ellipse Balusters

Each Deckorators CXT Rail Kit

ColonialRail.ai

CXTBracket.ai

(4) - In-line or stair brackets

(8) - 2" long

countersunk screws

(16) - 1" long

countersunk screws

(4) - 1-1/2" long

pan head screws

(2) - 2-1/2" long

countersunk screws

ConnectorWScrew.ai

SupportBlock.ai

(3) - 4" Support blocks

(3) - Support block

connectors

with screws

LowerRail.ai

(1) - Lower rail

RailRetainer.ai

(2) - Inner rails

Bit.ai

(1) - Drill bit

ContemporaryRail.ai

(1) - Upper rail (Colonial or Contemporary Style)

Step 1: Determine the number

of railing posts needed for your

deck. Post spacing is 8' on-

center. Example: A 16'x20' deck

attached to a building with a

4' access opening on one side

will require a total of eight posts

(ﬁg. 1).

Prior to construction, check with your local regulatory agency for

special code requirements in your area. Common railing heights are

36" and 42". Structural support should come from the continuation of

deck support posts that extend up through the deck ﬂoor or from railing

posts that are bolted to the inside of the rim or outer joists. Never

span more than 8' on-center between railing posts. Install railing posts

before deck boards are fastened to the joists.

Pre-drilling of all railing components is essential to successful

installation. Do not over-tighten screws. Read instructions completely

to get an understanding of how the product goes together and how each

piece affects the other.

ﬁg. 1

PAGE 1 - 8' CXT Rail_ENG

6475_3/14

Items you will need:

• Drill/power screwdriver

• Assorted drill bits

• Hammer

• Miter or circular saw with

ﬁne-tooth carbide tip blade

• Construction adhesive

• Marked speed square

• Two clamps

• Carpenter’s level

• Carpenter’s pencil

• Adjustable wrench or socket

wrench for bolts, etc.

• Safety glasses/goggles

• Assorted fasteners

(see instructions)

• Tape measure

PFS AA-652

For each 8' on-center railing section you will need:

One 8' Deckorators CXT Line or Stair Rail Kit that contains:

* (1) Upper rail

* (1) Lower rail

* (2) Inner rails

* (3) Support block kits that contain:

• 3 4" Support blocks

• 3 Support block connectors with screws

* (1) In-line or stair hardware kit that contains:

• 4 In-line or stair brackets

• 16 1" long countersunk screws

• 4 1-1/2" long pan head screws

• 8 2" long countersunk screws

• 2 2-1/2" long countersunk screws

• 1 Drill bit

• 1 Screw pack consisting of 40 screws

(use with Deckorators Baluster Connectors)

• 1 Post Sleeve Bracket placement template

Baluster options:

One Co-Extruded Composite Baluster Kit that contains:

• 20 – Balusters

• 40 – Baluster Connectors with screws

Classic, Estate, Twist or Ellipse baluster kits that each contain:

• 10 aluminum balusters

• 20 balusters needed per 8' on-center railing section

(Classic, Estate and Twist)

• 24 balusters needed per 8' on-center railing section (Ellipse)

and

Baluster connector or designer baluster connector kits

that each contain:

• 20 baluster connectors

• 1 kit needed per 10 balusters

Glass baluster kits that each contain:

• 5 glass balusters

• 20 stainless steel screws

• 12 balusters required per 8' on-center railing section

and

Glass baluster connector kits that each contain:

• 2 connectors

• 1 kit needed per baluster

Use rail kit without pre-drilled holes with Glass baluster kits.

One 40" or 52" Post Sleeve Kit that contains:

• 1 post sleeve

• 1 post base trim

One Post Cap for each post sleeve (sold separately)

1 2 3 4 5 6 7 8 9

Inhaltsverzeichnis

Seite 1 - Deckorators

Deckorators® CXT 8' Rail Installation InstructionsFor Installations Using Co-Extruded Composite, Classic, Estate, Twist and Ellipse BalustersEach

Seite 2 - PAGE 2 - 8' CXT Rail_ENG

Step 8: Assemble the lower inner rail and support block assembly. A support block is needed every 2' on-center. Check building codes for a maximu

Seite 3 - www.deckorators.com

PAGE 3 - 8' CXT Rail_ENG8' Rail Installation Instructions continuedStep 13: Measure the distance between the posts and trim the upper top ra

Seite 4

Capuchon de poteauTraverse supérieureVis 1 poVis2 poBalustreRaccordTrousses de blocs de support (3)4 x 4Poteau4 x 4Manchonde poteauCouvre-joint

Seite 5 - PAGE 2 - 8' CXT Rail_FRE

Étape 4 : Installez les lames : entaillez les lames aﬁn qu’elles se placent avec les poteaux pour balustrade 4x4. Laissez un espacement de ¼ po entre

Seite 6 - www.deckorators.com

Instructions d'installation de traverse de 8 pi suiteÉtape 13 : Mesurez la distance entre les poteaux et taillez la traverse la plus haute à la l

Seite 7

Qué necesitará:• Taladro/desarmador eléctrico• Cabezas de taladro diversas• Martillo • Sierra ingletadora o circular con hoja de punta de carburo •

Seite 8 - PAGE 2 - 8' CXT Rail_SPA

Paso 4 : Instale el tablado, corte las tablas de la terraza para ajustarlas alrededor de los postes del barandal de 4x4. Deje un espacio de 1/4"

Seite 9 - Coloque el barandal interior

Instrucciones de instalación de barandal de 8 pies continuaciónPaso 13: Mida la distancia entre los postes y recorte el barandal superior a la longitu

Kommentare zu diesen Handbüchern

Keine Kommentare

Deckorators CXT8 Rail Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Deckorators CXT8 Rail herunter. Deckorators CXT8 Rail User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Deckorators CXT8 Rail